Common Rail  Injector SimulatorCommon Rail  Injector SimulatorCommon Rail  Injector SimulatorCommon Rail  Injector Simulator
Common Rail  Injector SimulatorCommon Rail  Injector SimulatorCommon Rail  Injector SimulatorCommon Rail  Injector Simulator

Common Rail Injector Simulator

Overcurrent and short circuit protection

Support magnetic injector impedance measurement

Record number of users

Customizable boot LOGO

  • Support magnetic and piezo injectors(BOSCH, DENSO,DELPHI, PIZEO, CAT-L,CAT-H, Caterpillar);
  • Overcurrent and short circuit protection
  • Support magnetic injector impedance measurement;
  • On-board temperature sensor, overheat protection;
  • Record number of users
  • Customizable boot LOGO;
  • According to customer demand for customized software interface, operation, chassis appearance;
  1 Accessories and Interface Description

1.1 Check the accessories

After receiving the goods, please open the box and check box items are consistent with the packing list immediately if any parts are missing, please contact the service personnel.

1.2 Chassis Interface

Electromagnetic injector end (2-pin):

Description

Air outlet side

NANT Test Equipments Co.,Ltd

Injector drive

pin1

Injector drive

pin2

Piezo injector end (4-pin):

Description

Air outlet side

NANT Test Equipments Co.,Ltd

Injector drive

pin1  -

Injector drive

pin2  +

Empty

pin3

Empty

pin4

Count switch terminal (3-pin):

Description

Air outlet side

NANT Test Equipments Co.,Ltd

Count Normally open

Pin1

Counting common

Pin2

Counting Normally close

Pin3

 

  2 Operating Instructions

2.1 Chassis panel

NANT Test Equipments Co.,Ltd

2.2 Basic operation

2.2.1 Display interface:

NANT Test Equipments Co.,Ltd

  • Select the type of injector:BOSCH、DENSO、DELPHI、CAT-L、CAT-H、PIZEO
  • Current Injector conditions:VL、VE、LL、TL
  • the injector count method: T: according to the number of counts; 
  • injector counting time: T :0-2000 times 
  • injection signs: icon display indicates the beginning of the injector fuel injection; 
  • pulse width: 100 ~ 3000uS; 
  • injection frequency: 1 ~ 30Hz 
  • the count flag: Icon display indicates the injector start counting;

2.2.2 Key Features

2.2.2.1 ON/OFF button:

On / Off Injector;

2.2.2.2 COUNTE button:

  • Start / stop counting.
  • When the number is 0, the injector has been working, do not stop.

2.2.2.3 MODE button:

  • Short press MODE button to switch to a different injector conditions; (BOSCH、DENSO、DELPHI、CAT-L、CAT-H、PIZEO)
  • long press the MODE button to switch between test patterns and resistance injector test mode; (Valid only in the injection stopped)
  • After entering the resistance test mode, connect the injector first, and press the ON/OFF button once. After 2 seconds, the resistance of the injector will be displayed on the screen. The unit is milliohm.

If it is found that the measured resistance deviates greatly from the actual resistance, it should be calibrated.

Calibration method: In the resistance measurement interface, directly short-circuit the two clips of the injector, and then short-press the “Counte” key. A “#” symbol will appear at the upper right of the screen. After this symbol disappears, calibration is completed. Screen listing shows 0 mohm.

2.2.2.4 ADJ knob:

  • Consists of two parts function

A. Common parameter settings

The first step, Short press down to select the setting of the project, there is a corresponding position cursor display, divided into: Injector brand choice / count value / width / frequency, cycle through the four setting items, the current cursor location for the selected projects.

The second step, Rotate Left or Rotate Right, modify the current value of the item.

 

 

LEAVE MESSAGE

If you have any questions, feedback or comments, please fill out the form below and we will reply you back as soon as possible.

Cooperative
partner